Disclosed Automatic Urinal Flusher KEG-108D

The disclosed automatic urinal flush valve KEG-108D is normally installed on a wall mount urinal. It uses active infrared automatic sensor technology. When you stand in front of the auto flush valve, 2s pre-flush after detection; 6s Flush automatically after leaving. The sensor is integrated inside the valve.

  • Brand: KEGE
  • Item No: KEG-108D
  • 2s for pre-flush & 6s for after-flush
  • Automatically flush if no usage in 24 hours
  • Hygienic, bacteria and germs free without touching
  • Automatically adjust the sensor range of 40-80cm according to the actual use situation without manual adjustment.

Features:

  • Automatic on/off: when you stand in front of the auto urinal flush, 2s pre-flush after detection; 6s Flush automatically after leaving.
  • Automatically flush if no usage in 24 hours.
  • Low power indication: This may indicate it is time to replace existing batteries with new ones or there is not enough power going to the unit.
  • Water-saving: Water-efficient flusher valve reduces overall water usage without sacrificing water.
  • Energy-saving: 4AA alkaline batteries shall last approximately 3000 times/month for 1.5 to 2 years.
  • Healthy and Safe: Touch free, it can prevent the spread of bacteria and germs, convenience and hygiene.
  • Stainless steel panel and box, all copper solenoid flush valve: electronic part seal design, waterproof and moisture-proof.
  • It can be adjusted automatically within the range of 40-80cm according to the actual use situation without manual adjustment.
  •  Surface mounted design, suitable for various occasions, convenient installation.

DISCLOSED AUTOMATIC URINAL FLUSHER KEG-108D SIZE
DISCLOSED AUTOMATIC URINAL FLUSHER KEG-108D INSTALLATION

Auto Urinal Flusher Valve KEG-108D Specification

External Power Supply Applicable water pressure Applicable Water Temperature Ambient Temperature Feedwater caliber Flushing water volume

4XAA batteries

AC:110v-240V,50Hz-60Hz DC&AC combined 0.05-0.7Mpa 0.1-60℃ 0.1-45℃ G1/2” 1.5-4L(10s based on water pressure of 0.3-0.6Mpa)

Auto motion sensor for urinal flush valve

As the most important part, the work of the sensor is to forward the signals to the valve to turn on the urinal flusher after detecting your body. Its job is to inform the valve when to turn on or off the water when your body comes and leaves. The cover of the sensor is made of plastic ABS or PA and there is an electronic circuit board inside the sensor eye which also includes the led light.

We have more than 50 different sensor eyes and electrical wires for your selection. We can adjust sensor rang and flushing time by a remote controller. Normally the material of the sensor cover is plastic ABS or PA, the infrared beams can pass through it. We can also customize the sensor cover according to your products.

Automatic Urinal Flush Sensor KEG-K160

Working Principle

Active infrared touchless sensors use the emission and reception of infrared beams to detect the presence and/or movement of objects or people in their field of detection. The technology is ideal for applications requiring a long and narrow detection range.

infrared sensor technology

Touchless Urinal Flusher Valve Troubleshooting

Problem Possible Reason Suggested Solution
No water flow Batteries run out Replace batteries
Dirt on the sensor surface Clean the sensor surface
The main water supply is shut off Turn the main water supply on
Dirt on water filter net Clean the water filter net
Water pressure is not applicable Refer to the technical specification
Have a continuous water flow problem Batteries run out Replace batteries
Low water pressure Refer to the technical specification

People who are asking more:

Automatic urinal flusher uses infrared sensor technology that when you stand in front of urinal ceramic, the sensor detects and gives a pulse signal to the solenoid valve to open and give 2s pre-flush, then stop. After you leave, again 6s flush automatically. Program control all the process.

Auto urinal flushers need electricity for sure. Both the sensor and solenoid valve works need electricity power. Normally DC: 4xAA alkaline 6V batteries.

Sorry that there is no push button to flush, this s an automatic sensor touchless urinal valve with two-step flush: 3-sec pre-flush + 8-sec post flush. Avoid touch, more healthy,y and clean. If you want push button auto urinal flusher, please click here.


We can adjust sensor rang and flushing time with a remote controller.


Related products:

Related articles: