Diy touch free kitchen faucet solution with touchless device add on normal faucet

diy Touchless kitchen faucet ADAPTER solution

How to convert your normal standard kitchen faucet to be a smart touchless kitchen faucet? With KEGE DIY touchless kitchen faucets adapter and easy install, then your regular kitchen faucet will turn to be a touchless kitchen faucet. Wave the sensor, water comes out automatically, wave again water stops, or water stops automatically after 3mins continuous flow. It is so easy and turns your kitchen to be hygienic, healthy, and safe. If you are interested in a touchless kitchen faucet but with a little budget, then the DIY touchless kitchen faucet adapter is just your selection.

KEGE can offer the whole solution for the DIY touchless faucet kitchen adapter. No matter you are Kohler, Moen, Delta, Grohe, Home depot, Glacier bay, or American standard kitchen faucet, with our adapter, it can all turns your regular faucet to be a smart touchless kitchen faucet, our adapter suits most of the kitchen faucet in the market because we have two different sizes of mounting connectors. We also have different colors to match your kitchen faucet colors.


  • Touchless Motion sensor: Keeping the faucet handle on, wave the sensor without touch, water flows, wave again, water stops. Water stops automatically after 3mins continuous flow.
  • Convert a manual regular kitchen faucet to a touchless kitchen faucet.
  • There are two different sizes of mounting connectors to fit different kitchen faucets, which means our sensor device will match almost all kinds of kitchen faucets.
  • Easy installation and cleaning.
  • Power detection. Close the solenoid valve water stops automatically when power failure or low power.
  • Low power indication: Sensor LED continuously flashes 5 times to indicate low power. This may indicate it is time to replace existing batteries with new ones or there is not enough power going to the unit.
  • Healthy and Safe: with touch free kitchen faucet, it can prevent the spread of bacteria and germs. It’s not only time-saving, but also hygienic.
  • Sensor distance adjustable by a remote controller.
  • Long life time: Battery shall last approximately 25 circles per day for about 1-2 years.

KEGE DIY Touchless Faucet Adapter

Below we have two types of touchless faucet adapters, one with alkaline battery and one with lithium battery.

The touchless faucets adapter with lithium battery has a super long life span of 5 years using and no need to recharge the battery. The touchless faucets adapter with the alkaline battery has a shorter life span of 1-2 years using and it is quite easy and cheap to change the batteries because it only requires 2 AA normal batteries that you can buy them easily from the market.

How does KEGE touchless faucet adapter work?

Simple function, just wave the sensor before our adapter, the water comes out automatically. Wave the sensor again, water automatically stops.

Active infrared touchless sensor

Active infrared sensor

Active infrared touchless sensors use the emission and reception of infrared beams to detect the presence and/or movement of objects or people in their field of detection. The technology is ideal for applications requiring a long and narrow detection range.

diy Touchless kitchen faucet solution

Technical  Parameters Work Power Over-Time Protection Static Power Consumption Sensor Range Sensor Distance Customizable Parameters Opening Sensitivity Closing Sensitivity Adjustable Parameters
DC4.6V~6V Side:3mins  Bottom: 1min

1.Side:4cm~12cm (distance to hand)  

2.Bottom:5cm~15cm (distance to hand)

6cm (Distance to hand) 1. opening sensitivity <0.3s <0.3s Sensor distance adjustable by a remote controller
2. closing sensitivity
3. over-time protection
Application Kitchen faucets with manual handle


Diy Touch free Kitchen Faucet adapter

With this device, simply install and will convert the manual kitchen faucet to touchless kitchen faucet.


Touchless kitchen faucets use infrared sensor technology that allows you to start the flow of water without touching the faucet. Instead, just placing your hand under the spout sensor, the sensor will give the solenoid valve a signal to open, then the water will start flow; When you take your hand away, the sensor will indicate the solenoid valve to close, then water flow will stop.

In the future modern smart home, a touchless kitchen faucet is also one core part. They’re cool, for one thing, as their motion sensors always give you some sort of smart, modern techy feelings. Plus, a touch free faucet keeps your fixture and kitchen clean, it’s a good hygienic choice and decreases the risk of contracting viruses and diseases.

Touchless kitchen faucets need electricity for sure. Both the sensor and solenoid valve works need electricity power. Normally three choices: DC 6V: 4xAA alkaline batteries; AC: using a transformer to transfer power from 220V/380V to 6V; Both DC/AC models existed, firstly use AC power to work, if AC no power then DC start to work.

6V with 2xAA alkaline batteries shall last approximately 25 circles per day for about 2 years.

1. Battery issue: battery no power or battery installed in the wrong direction.
2. Sensor issue: the waterproof cable issue or sensor got damage.
3. Solenoid valve issue: the filter in the valve blocked or the valve is damaged.
For more please check the troubleshooting of touchless faucets.

Yes. Time-up protection design can avoid overflowing by closing the electromagnetic valve automatically by the end of three minutes of running water until it is activated next time, which can effectively prevent a “flood” usually caused by careless adults or naughty kids.

The original faucet must be on for the touchless to work. If you don’t want it to accidentally activate, you can turn off the original handle.

+86 158 5847 1917
315th,Tongning road,Hongtang,Jiangbei, Ningbo,China,315033

How to install DIY touchless faucets adapter?


  1. Please read the instructions carefully.
  2. The sketch map is only for reference. Product appearance and accessories may differ from illustrations in the manual.
  3. Please confirm to use a standard 2AAA alkaline battery, make sure the battery polarity is installed correctly.
  4. Please prepare a wrench, which is used to screw the connector


  1. Turn off the kitchen faucet handle and unscrew the faucet nozzle.
  2. Select the correct male/female connector with a sealing washer.
  3. Put the nut into the kitchen faucet and tighten the nut.
  4. PUT the DIY sensor tap body align with the connector, sensor faces forward, plug into the connector.
  5. Turn on the handle, the installation is complete, If there is an abnormality, please check the troubleshooting.

For more details, please check the pdf file or view our blog here. You can also check the installation manual inside the package.

touchless faucet adapter installation manual



Please use a damp towel or cotton cloth to wipe gently.


Please avoid any rocking or violent motion.


Please DO NOT use acid / alkaline detergents for cleaning.


Related solutions: